Home » Products » Dry Type Reactor/Inductor/Choke » Load Bank Reactor/Inductor/Choke

Load Bank Reactor/Inductor/Choke

Overview

Load Bank Reactor/Inductor/Chokes are used in conjunction with back-up power generators which need to be run on a regular basis. Performing this function without or with little load may lead to a phenomenon called“wetstacking” which shortens the life of the diesel engine that runs the generator. The load bank is often specifically built to reflect the exact electrical characteristics, resistance, capacity and reactivity of the facility in question.

Application
This series of reactors are usually used in the resistive-reactive load banks for testing and maintenance of large AC power systems at rated kVA. Resistive-Reactive Load Banks offers a 0.80 power factor load and is designed for testing large generators, switchgear, transformers and UPS systems.
1. It is used to simulate inductive load in a system.
2. It is also used to compensate capacitive current in a system.
3. Inductive load must be connected across phase in a system.

Conditions of use
1. The highest temperature: +40 ℃
2. The lowest temperature:25 ℃
3. Altitude: <1000 m
4. The highest monthly average relative humidity: 90% (20 ℃)
5. Installation location: installed in no fire and explosion danger, serious foul, chemical corrosion and the site of violent vibration, indoor or outdoor.

Specification
Design: Iron core, Dry type, Natural air cool (AN) for indoor use
Operating temperature: Max. temperature rise, 90ºC at 40ºC ambient.
Over current: 105% rated current / voltage for 2 hours.
Inductance linearity: Linear type, up to 125% rated current.
Thermo-protection: Thermostat 145ºC NC included.
Insulation Class: F, Vacuum pressure impregnated varnish. Pure Nomex paper is used as layer insulation.
Dielectric strength: 3.0KV – 1 minute tested.
Construction: Core: Depend on size, 0.35 -0.5 low loss silicon steel. Multiple (distributed) gaps design.
Coil: Aluminum or copper wound coil.
Connection: Star, Star point is connected in the factory.
Noise: Depend on size, most shall be below 65 db.
Protection: could be designed by customer requirement
Standard apply: IEC289:1987 as shunt reactor
Technical parameter table is for your reference only ( Aluminum coil),if you have any other special requirements , please send us the detailed information to the email in the website.

Technical Parameters
Line Reactor and DC Reactor Compatible with CONVO Inverter GI (0.75~280KW), PI (1.5~280kw), ZS5.5~45kw)
Inductive load A B C D E H-holes Wt
kVAr Un Volt/Hz Irated - A Loss - Watt mm mm mm mm mm mm kg
2.5 415V 50Hz 123 200 240 140 113 136 10 11.5
5 415V 50Hz 7 226 255 310 235 125 170 10 25
10 415V 50Hz 13.9 260 300 310 255 160 170 10 41
15 415V 50Hz 20.9 310 360 360 255 175 320 10 63
20 415V 50Hz 27.9 400 380 380 280 10 78
25 415V 50Hz
30 415V 50Hz 41.8 550 470 380 300 12 98
50 415V 50Hz 69.7 645 550 500 300 12 175
75 415V 50Hz
100 415V 50Hz 139.4 1250 620 560 330 12 270
150 415V 50Hz 210 2300 780 620 400 12 400
uctor/Choke" bigimg="/upload/3351/o/18_load-bank-reactor_05.jpg" setsize="600,470" src="/upload/3351/o/18_load-bank-reactor_05.jpg" />
Inquiry Form